Hi All,
I'm very new to Linux, using it for about 3 days. I have a Vostro 1710 on Fedora 15 and the SD card does not seem to be working. I say 'seem' as I expect to have a window pop up with the card contents when I insert it - which is not happening. I've tried a few fixes from various forums, including this one, but my problem still persists.
I've checked the BIOS and the card seems to be enabled.
Quote:
[david@localhost ~]$ lspci
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c)
00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (primary) (rev 0c)
00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (secondary) (rev 0c)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03)
00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 03)
00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 03)
00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3)
00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03)
00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03)
06:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01)
07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
08:05.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02)
08:05.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 02)
08:05.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01)
|
And..
Quote:
[david@localhost ~]$ dmesg |grep sd
[ 1.544000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.544133] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 1.544208] sd 0:0:0:0: [sda] Write Protect is off
[ 1.544211] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.544242] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.601290] sda: sda1 sda2 sda3 sda4 < sda5 >
[ 1.601889] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.922451] sdhci: Secure Digital Host Controller Interface driver
[ 2.922454] sdhci: Copyright(c) Pierre Ossman
[ 2.972208] sdhci-pci 0000:08:05.2: SDHCI controller found [1217:7120] (rev 2)
[ 2.972227] sdhci-pci 0000:08:05.2: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 3.397161] dracut: Scanning devices sda5 for LVM logical volumes VolGroup/lv_root VolGroup/lv_swap
[ 22.599700] systemd-fsck[690]: /dev/sda3: clean, 44/128016 files, 66852/512000 blocks
[ 22.827241] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 22.847646] SELinux: initialized (dev sda3, type ext4), uses xattr
|
As far as I can see it should work?
I have looked in /var/log/messages after removing and inserting the card a few times and there is nothing in there that seems to suggest the card is mounting.
EDIT
I insert the card with messages open but no response:
Quote:
[david@localhost ~]$ sudo tail -f /var/log/messages
[sudo] password for david:
Sorry, try again.
[sudo] password for david:
Sep 28 14:16:55 localhost dhclient[1181]: DHCPREQUEST on wlan0 to 192.168.22.1 port 67
Sep 28 14:16:55 localhost dhclient[1181]: DHCPACK from 192.168.22.1
Sep 28 14:16:55 localhost dhclient[1181]: bound to 192.168.22.11 -- renewal in 149 seconds.
Sep 28 14:18:34 localhost dbus: [system] Activating service name='org.freedesktop.PackageKit' (using servicehelper)
Sep 28 14:18:34 localhost dbus: [system] Successfully activated service 'org.freedesktop.PackageKit'
Sep 28 14:19:24 localhost dhclient[1181]: DHCPREQUEST on wlan0 to 192.168.22.1 port 67
Sep 28 14:19:24 localhost dhclient[1181]: DHCPACK from 192.168.22.1
Sep 28 14:19:24 localhost dhclient[1181]: bound to 192.168.22.11 -- renewal in 149 seconds.
Sep 28 14:20:46 localhost dbus: [system] Activating service name='net.reactivated.Fprint' (using servicehelper)
Sep 28 14:20:46 localhost dbus: [system] Successfully activated service 'net.reactivated.Fprint'
|
Linear Mode
